Vitera Full Face Mask – Fisher & Paykel
Since full face masks for CPAP have more surface area than nasal masks, they can be a bit more challenging to fit. Fisher & Paykel’s new Vitera full face mask aims to put an end to leak chasing. The Vitera delivers stable, secure, dynamic support all night long so that you wake up rested. The F&P Vitera adapts with you as you move, regardless of how much you move. The Vitera’s RollFit XT seal and low profile stability bar sync with its breathable headgear to keep you cool, comfortable, and in your sleep therapy zone all night.
- Designated mask fitting guide App for iOS and Android phone
- A full face mask design that fits most people
- Auto-adjusting fit to reduce leak and reduce pressure on the nose
- Headgear wicks moistures and heat
RollFit XT seal conforms again and again for your comfort
The RollFit XT seal is an update to the RollFit seal used in prior generations of Fisher & Paykel masks. The clever engineering of Fisher & Paykel’s RollFit XT seal minimizes the need to overtighten the headgear in response to leaks. The cushion gently rocks back and forth at the bridge of the nose as you move. By automatically adapting the angle of the mask, the RollFit XT design blocks any significant gaps without the need to tighten headgear. The rocking action of the seal automatically reduces pressure on the bridge of the nose. The cushion also has strategically located thickened and thinned sections to enhance comfort and support. The RollFit XT seal extends 93% further than the RollFit cushion did and is also deeper and narrower around the nasal bridge. These updates allow the cushion to fit a broader range of face shapes and further minimize leaks out the top of the cushion into the eyes. Three sizes are available for the Vitera: Small, Medium, and Large.
Stability bar delivers dynamic support
The RollFit XT seal works in tandem with the stability bar to continually fine-tune and optimize the Vitera’s mask fit. The stability bar runs from the top of the nasal cushion to the center of the forehead. The stability bar relies on a wide anchoring zone defined by the top and bottom straps of the headgear. The broader zone of support gives the RollFit XT seal the space it needs to roll and adjust to keep the mask reliably seated regardless of the user’s position.
VentiCool headgear keeps you cool and dry with a personalized fit
The Vitera’s adjustable headgear features VentiCool fabric, a custom-made breathable cloth. The VentiCool fabric allows heat and moisture to escape to keep you cool and dry, especially behind the head. The headgear attaches to the Vitera’s frame with clips with tactile grips, so it’s a cinch to reach behind the ear to find them. The headgear comes in two sizes (Small and Medium/Large) with a forehead strap and a crown strap so that you can adjust the fit to be just right for you. After your good night’s rest, take the headgear off and clip the forehead straps together with the Vitera’s unique forehead clip so that you are not untangling headgear at bedtime.
Sizing and Fitting
Now the F&P myMask mask fitting App is up, download to fine-tune your Vitera Mask today:
For Apple Download Here
For Android Download Here
Selecting the right size mask and headgear is critical to your comfort and satisfaction with any sleep apnea mask. Overtightening any mask can make leaks worse. Thanks to the components of the RollFit XT seal, the Vitera does not need to be super snug against the face. Users should be able to pull the mask gently away from the face without removing the headgear.
The appropriately sized full face mask should sit below the mouth and at the bridge of the nose. The mask should not be in the eyes or on the lower lip. A sizing guide is available to hold against the face. The Vitera mask retains the VisiBlue highlights introduced in other models of Fisher & Paykel CPAP masks. Blue color cues placed at crucial places on the mask and headgear orient you quickly to the mask, making it easier to put on. You will not wonder if it is backward, inside out or upside down.
To get the best performing fit, follow these steps in order:
- With one side of the headgear unclipped from the frame, place the silicone seal over the mouth and nose.
- Pull the headgear over the head.
- Hook the headgear clip to the frame.
- First, adjust the bottom gray straps to secure the cushion under the mouth.
- Next, adjust the blue forehead straps to secure the cushion gently against the nose.
Pro Tip: The blue forehead straps should rest above the ears. The crown strap can be adjusted to get the blue forehead straps properly positioned.
Make additional adjustments to the straps once you are in a sleeping position with the CPAP machine turned on. If you find that you must overtighten the headgear, consider a different size seal or different size headgear.
Recommended cleaning frequency
- Daily: nasal cushion and frame including elbow, swivel, and clips
- Weekly: headgear
Please note: the elbow and swivel do not detach from the mask frame.
- Wash in warm soapy water using a mild dish soap.
- Rinse thoroughly in clean water.
- All parts should be air dried out of direct sunlight.
Important: Do not clean with products containing alcohol, scents, antibacterial agents, antiseptics, bleach, chlorine, or moisturizers. Do not soak any parts for more than 10 minutes.
Operating Range: 4-30 cm H20
Can I interchange some parts from my other Fisher & Paykel masks with the Vitera mask?
No. The Vitera is designed to work only with its own seal, headgear, and frame. Mixing and matching parts from different models of masks (even from the same manufacturer) results in frustration at best but can also be dangerous.
My doctor keeps recommending that I wear a full face mask, but I have not found one that keeps air out of my eyes. Will the Vitera help with this problem?
The RollFit XT seal and the stability bar work together to balance the mask on the bridge of the nose. This synchrony seals the cushion at the top and keeps air from escaping towards the eyes. The forehead strap that fits just above the ears pulls the mask toward the tip of the nose as well. A crown strap lets you get that forehead strap into just the right position so that it also helps keep a seal on top of the cushion.
Often the best way to resolve a leak is to lift the cushion off the face and reseat it gently. Reseating smooths out cushion wrinkles.
Since the mask covers my mouth, will I be ok if my CPAP machine stops working?
The Vitera has exhaust ports on the cushion and side vents on the elbow. Also, the headgear should be worn loose enough that you can pull the mask away from your face without unhooking a clip or removing the headgear.
Final CPAPMan Comment
Fisher & Paykel’s latest (in 2019) CPAP mask unites several unique technologies to deliver effective, comfortable CPAP therapy. The Vitera gives a gentle full face mask fit that continually tailors itself to correct leaks regardless of sleeping positions or facial movements. The Vitera takes the work out of full face mask use. Order today from CPAPman to get a cool, comfortable night’s rest with the full face Vitera mask from Fisher & Paykel Health Care. The Vitera comes in three sizes of masks and two sizes of headgear. CPAPMan’s customer service can help you find just the right size for you!
|Model||VIT1SA, VIT1MA, VIT1LA, VIT1SMLA|
|HCPCS Code||A7034, A7035|
INCLUDED WITH ITEM
- Fisher and Paykel Vitera Full Face Mask
- VentiCool Headgear
- RollFit XT Seal (selected size: small/medium/large)
- Easy Frame with Stability Bar
- Use and Care Guide
No customer reviews for now. Be the first to share your thoughts with other customers.
Have a question on this item? Ask here and we will answer it in 12-24 hours, usually in a few business hours! Questions and answers will appear here after we answer. You may also have email notifications.